top of page

How to Choose and Install a Gas Fireplace Insert in a Masonry Fireplace

Daniel Rochon
Oct 20
4 min read

Updated: Nov 6

A practical guide to planning a safe gas insert installation

Replacing an older wood-burning setup with a gas fireplace insert can give an existing masonry fireplace a refreshed appearance and a more convenient way to add heat. This guide walks through the main stages, from selecting a suitable unit to completing the final safety checks.


Exact requirements vary by insert model, fireplace, venting arrangement, and local building codes. Use this overview alongside the manufacturer’s instructions for the specific product rather than treating it as a substitute for them.


Safety first: Gas, venting, and electrical work can create serious hazards. Qualified professionals should handle specialized installation work, including the parts of the project that require licensed expertise or code compliance.

Gas fireplace insert in a masonry fireplace

1. Measure the Fireplace and Choose an Insert

Begin by measuring the existing masonry fireplace opening carefully. The insert needs to fit the available space, so record the opening dimensions before comparing models. Consider the heating capacity, preferred appearance, and fuel source that best suit the room and your home.


"Pro Tips Selection Factors Chart"

Selection factor

What to consider

Fit

Compare the insert with the measured fireplace opening.

BTU output

Review the model’s heating capacity for your project.

Style

Choose between a traditional log appearance and a contemporary design with glass media.

Fuel type

Confirm whether the unit is designed for natural gas or propane.

2. Prepare the Masonry Fireplace


Before the gas insert installation begins, clean the fireplace thoroughly and remove ash, debris, and any obstructions. Look for structural concerns in the masonry and address them before proceeding. The chimney and flue should also be checked to confirm that they are in suitable condition and meet applicable safety requirements.

  • Clean the firebox and remove debris.

  • Clear obstructions from the fireplace and flue.

  • Check the masonry for structural problems.

  • Confirm that the chimney and flue meet safety requirements


Clean masonry fireplace

3. Install the Required Venting System


A gas fireplace insert needs a properly installed venting system to exhaust combustion gases safely. Depending on the model, the system may use a flexible vent liner or a rigid vent pipe. Follow the manufacturer’s directions for the selected insert, and have qualified professionals complete specialized venting work.


4. Connect the Gas Supply


Check whether the fireplace already has an appropriate gas connection. If it does not, the project may require a new gas line. A licensed professional should install and connect the gas supply to the insert in accordance with local building codes and safety regulations.


5. Position and Secure the Gas Insert


Place the gas fireplace insert into the prepared masonry fireplace and position it as directed by the manufacturer. Secure the unit properly, then connect the gas supply, venting system, and any required electrical components according to the installation instructions.



6. Test the Unit and Adjust Its Settings


After the installation is complete, test the gas fireplace insert to make sure it operates as intended. Use an approved gas-leak detection solution to check for leaks. Adjust the flame height, pilot light, or other settings only as described in the manufacturer’s guidance.


Masonry gas fireplace insert in a modern setting

7. Follow Operating and Safety Instructions


Read and follow the operating instructions and safety guidance supplied with the gas fireplace insert. Keep a working carbon monoxide detector in the room where the unit is installed, and follow the manufacturer’s recommendations for safe use and care.


-Enjoy Your Updated Masonry Fireplace


A properly selected gas insert can refresh the look of an older fireplace and improve its heating efficiency. Because the project may involve gas, venting, and electrical work, homeowners who are not fully qualified should rely on experienced professionals to complete the installation safely and correctly.


Ready to upgrade your old wood burning fireplace? Contact us to start planning your project! info@stauv.com


FAQ


1. Will a Gas Fireplace Insert Fit My Existing Fireplace?


  • The Answer: Most inserts are engineered to slide into existing open-brick or factory-built fireboxes, provided you take accurate height, width, and depth measurements of the interior cavity. Metal trim kits ("surrounds") are used to close any gaps between the new insert and the old opening. 


2. How Much Does a Gas Fireplace Insert Cost?


  • The Answer: Total costs typically range from $6,500 to $12,000, with an average around $7,500 to $9,000. Final pricing depends heavily on whether you need a new gas line run or custom interior finishing like tile or mantels. 


3. Do I Need a Chimney or Venting?


  • The Answer: Almost all gas fireplace inserts are direct-vent systems. They require running two aluminum flex liners down your existing chimney (one for fresh air intake and one for exhaust fumes) to protect indoor air quality.


4. Can I Install a Gas Insert Myself?


  • The Answer: Professional installation is strongly recommended. Handling high-temperature chimney liners, tapping into home gas supply lines, and meeting local building code clearance rules require licensed technicians to ensure safety and code compliance.


5. Will It Work During a Power Outage?


  • The Answer: Many modern gas fireplace inserts operate using a millivolt standing pilot or a battery-backup ignition system, meaning they can continue to provide radiant heat even when the power goes out. (Units that rely strictly on a 120V blower or electric-only ignition will not run without power). 


6. How Efficient Are Gas Inserts Compared to Wood?


  • The Answer: Traditional open wood-burning fireplaces are notoriously inefficient (losing most of their heat up the chimney), whereas gas fireplace inserts typically achieve 70% to 85% energy efficiency. They are ideal for "zone heating"—turning down your central furnace and warming the specific room you use the most. 



Daniel Rochon Stauv pour Artefo Inc.

Daniel Rochon for Artefo Inc.


A specialist in chimneys, stoves, and fireplaces, Daniel turns technical details into simple, accessible advice. Through expert content, he clears up buyers' uncertainties and highlights the essentials, helping them choose and use their equipment with confidence.

Comments


bottom of page